How To Remove Aluminum Window Frame From Stucco

Hello,

I fabricated a previous mail service with questions nigh putting in a larger window in our bath. Our house has a stucco outside. We have decided to install a new construction Milgard Tuscany window. The size will exist approximately 48"x 18". The window store recommended removing the erstwhile window and measuring the crude opening earlier ordering the new window. The frame that is visible without removing the stucco is 46 vii/8" x 11 one/2".

Windowdog posted these instructions for removing the window.

"You don't have to tear upward the stucco. Here is a good method. Get a diamond blade for your circular saw. Go an expensive high quality i. On the outside, right NEXT to the exposed aluminum frame, cut through the stucco AND the nailing fin. Experiment with your bract depth considering you don't want to be cutting into the stud. Diamond blades don't work so well on wood! Be careful on the corners to get a full cut - yous'll have to go by 3/4" to compensate for the circular shape of the blade. When you're finished, the old window volition elevator out if it doesn't fall out, and then don't agree on to the window when yous're cutting. Also article of clothing a mask because this is very dusty. At this signal, yous should end upwardly with a clean cutting in the stucco. You should measure out your window to be app that size, and you tin can practise that before cut. Requite yourself a minimum of an extra one/4 inch all the way around for easy fitment betwixt the stucco. You will virtually probable exist backside the sheetrock at that betoken, but that's not for sure. In one case yous do one, you'll know how to do the others better. Worse case, y'all'll have to cut the stucco twice on the beginning ane. Exercise Non forget to flash/drip cap above the new window. Y'all can get up in there with a sawzall bract and cut the nails to remove the upper fin, which should give y'all plenty of clearance for your baste cap. Go ahead and rip out your sheetrock earlier installing the new window, and so only jamb up to it in one case it's determined where it will sit. You won't loose much glass area, if any, if you do it this way.

The new window, in this state of affairs, volition stick out past the stucco app 3/8 of an inch. You will be able, hopefully, to put a nice neat dewdrop of caulk around information technology that style, with no raw stucco edge showing. Be certain that you measure for this from the inside surface of the wall effectually the window all the way effectually, because stucco can be much much more uneven than the within sheetrock.

Don't forget you can mensurate where the studs are past measuring betwixt the sheetrock on the within and calculation for the thickness of the sheetrock. Compare this measurement with what you go measuring the exposed aluminum frame on the outside - Simply, use your within stud to stud measurements for your basis of determining the new window size. Besides, practise not forget, window sizes are e'er width kickoff. width x peak. E'er.

If this sounds similar too much for you, bite the bullet and have the pros do it. If you don't know what yous're doing it's not hard to butcher this kind of job. Worse worse example, you're patching stucco, simply that volition always have a tendency to crevice where you patched it.

And please be conscientious with ability tools on ladders. E'er have a helper or 2. Preferably 1 to steady the ladder, and one to hold the window. Tie off the ladder, necktie off yourself."

We are going to accept an experienced friend do the install but I'yard hoping we can remove the window ourselves. Here is a photograph of the exterior:

Windowdog, I'm wondering why we should cut through the nailing fin. I get that this method would not impairment as much of the stucco. However, since the new window will have a nailing fin, how will information technology fit into the opening if we don't cutting around the old fin?

As you can run into, the stucco needs painting anyway so we're not worried nigh matching the color. Nosotros hardly ever come across this side of the house. If we add wood trim, information technology would exist for convenience rather than because we're eager to dress upwards the windows. Eventually, we'll also be replacing the bedroom window shown in the photo. Would wood trim piece of work around this window even though it it raised from the wall? If we install would trim, will the stucco still demand to be patched underneath information technology?

You mentioned that the stucco volition take a tendency to crack where it is patched. Tin can the cracking exist prevented by making a jagged border around the window instead of cutting a straight border? We're leaning toward installing wood trim. The window store rep asked me if we want a stucco fundamental on the new window. She said that if we're adding wood trim, it may not fit well with the stucco key. What type of frame should nosotros guild for this window?

Sorry for the long mail.

Source: https://www.houzz.com/discussions/2634879/removing-window-from-stucco

Posted by: wilsonliche1953.blogspot.com

Share this post